Printek FORMSMASTER 8000SE Operator's Manual Page 99
- Page / 127
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
91
USING THE OPTIONAL SETUP
MODULE
Introduction
The optional Setup Module is a small cartridge that plugs directly into the
RS-232 Serial connector on the rear of any FormsMaster 8000se series
printer. This module is used to store a second copy of the current Setup
configuration of the printer. This may then be used to restore settings after a
printer is serviced or to copy the same configuration settings to another
printer. These uses are discussed immediately following the installation
instructions.
Setup Module Installation
To install the Setup Module, perform the following steps.
1. Turn off power to the printer.
2. Disconnect the cable plugged into the serial port if one is present.
3. Plug the Setup Module into the serial port.
4. If a cable was present in step 2, reconnect it to the connector on the
rear of the Setup Module.
5. Turn on power to the printer.
6. If this is not the first time the Setup Module has been connected to a
printer, then proceed with step 7.
If this is the first time the Setup Module has ever been attached to a
printer, the printer will temporarily display the following message and
the ONLINE indicator will be yellow. When the message disappears,
- FormsMaster 8000se 1
- Part Number 5613 2
- TABLE OF CONTENTS 6
- USING REMOTE SETUP 83 7
- PRINTER CONFIGURATION 41 7
- FORM CONSTRUCTION 73 7
- ADVANCED SETUP FEATURES 79 7
- Introduction 91 8
- INTRODUCTION 9
- Manual Contents 10
- GETTING STARTED 13
- Interface Set Up 14
- Installing the Ribbon 15
- Cartridge” on page 10 15
- Parallel Interface Connector 16
- REORDER NUMBER 90729 18
- Loading Paper 23
- Aligning Print” 24
- FormsMaster 8003se Tractors 25
- Printer Self-Test 27
- Off is displayed on the 28
- DAILY OPERATION 29
- Control Panel Features 30
- Flashing Green: 31
- Flashing Red: 31
- Yellow: 31
- Flashing Yellow: 31
- Audible Alarm: 31
- FORM FEED/LOAD 32
- <not 33
- Loading Forms” 34
- Aligning 34
- PRINTER 34
- CONFIGURATION” 34
- Selecting and Loading Forms 35
- FormsMaster 8003se tractors 36
- New form loaded in tractors 39
- Bottom of form at tear bar 40
- Tearing off a Form” 40
- Tearing off a Form 41
- Tearing off a form 41
- GETTING STARTED” chapter 43
- Aligning Print 44
- Left/Right option 45
- Common Error Conditions 46
- Ribbon Checking” 47
- PRINTER CONFIGURATION 49
- Forms Menu 52
- A through Z 53
- 0 through 9 53
- No, the 54
- Top Margin 55
- Bottom Margin 55
- Characters Per Inch 55
- Left Margin 56
- Right Margin 56
- Draft Speed 57
- Impact Force 57
- Language 57
- Zero Style 58
- Unidirectional Printing 58
- Interface Menu 59
- Emulation 60
- Automatic Carriage Return 60
- Automatic Line Feed 60
- Characters 61
- Minimum Buffer 61
- Baud Rate 61
- Data Bits 61
- XON/XOFF Handshaking 63
- ETX/ACK Handshaking 63
- RTS/CTS Handshaking 63
- IP Address 66
- Gateway Address 66
- Options Menu 68
- Paper Out Fault Action 69
- To use this feature: 70
- Top of Barcode 71
- Top of Oversized 71
- User Language 71
- Reprint Page Size 71
- Truncate Long Lines 72
- Ribbon Checking 72
- Ribbon Life 73
- LF*, CR 74
- 72*, 70 76
- Test Menu 77
- Print the Menus 78
- Test Mode 78
- FORM CONSTRUCTION 81
- Form Layout Considerations 82
- MAINTENANCE AND 83
- TROUBLESHOOTING 83
- Preventive Maintenance 84
- Obtaining Service 84
- ADVANCED SETUP FEATURES 87
- USING REMOTE SETUP 91
- Remote Setup Example File 96
- USING THE OPTIONAL SETUP 99
- Copy to 100
- Using the Setup Module to 102
- PRINTER RESET CONDITIONS 103
- CONTROL CODE AND ESCAPE 105
- SEQUENCE SUMMARIES 105
- ANSI x3.64 Emulation 106
- Epson FX Emulation 107
- Epson FX Emulation (cont.) 108
- IBM Proprinter Emulation 109
- LA-120/210 EMULATION 110
- Simple TTY Emulation 111
- Printek Emulation 112
- ASCII CHARACTER TABLES 113
- PC Font Character Set 114
- EBCDIC Font Character Set 114
- OCR-A Font Character Set 115
- ML (850) 117
- SPECIFICATIONS 119
- Computer Interface 121
- Operator Controls/Indicators 122
- Reliability 122
- Warranty 122
- Environmental Specifications 123
- Options 123
- GLOSSARY OF TERMS 125
- GLOSSARY 126
© 2020, manymanuals.com. All rights reserved. | 0.875 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals